plustek@linuxhacker.org

Hello, 
I think i have  followed  all the instructions but it's always the same 
problem: No scanners were identified! 
In dll.conf, i've just let the plustek  and the net entries.
These are the logs:


[root@localhost fab]# cat /proc/bus/usb/devices
...
P:  Vendor=03f0 ProdID=0605 Rev= 1.00
S:  Manufacturer=Hewlett-Packard
S:  Product=HP ScanJet 2200C
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=usbscanner"



"[root@localhost fab]# modprobe -v scanner vendor=0x03F0 product=0x0605
/sbin/insmod /lib/modules/2.4.19-16mdk/kernel/drivers/usb/scanner.o.gz 
vendor=0x03F0 product=0x0605"



"[root@localhost fab]# /usr/local/bin/sane-find-scanner
  # No SCSI scanners found. If you expected something different, make sure 
that
  # you have loaded a SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x03f0, product=0x0605) at /dev/usb/scanner0
found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x0605 [HP ScanJet 
2200C]) at libusb:001:002
  # A USB device was detected. This program can't be sure if it's really
  # a scanner. If it is your scanner, it may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.
  # Scanners connected to the parallel port or other proprietary ports can't 
be
  # detected by this program."



"[root@localhost fab]# /usr/local/bin/scanimage -L
No scanners were identified. If you w...."


"sanei debug] Setting debug level of dll to 12.
[dll] sane init: SANE dll backend version 1.0.6 from sane-backends-1.0.9
[dll] add backend: adding backend `net'
[dll] add backend: adding backend `plustek'
[dll] load: searching backend `plustek' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-plustek.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-plustek.so.1'
[dll] init: initializing backend `plustek'
[sanei debug] Setting debug level of plustek to 12.
[plustek] Plustek backend V0.44-10, part of sane-backends 1.0.9
[plustek] ># Plustek-SANE Backend configuration file<
[plustek] ># For use with Plustek parallel-port scanners and<
[plustek] ># LM9831/2/3 based USB scanners<
[plustek] >#<
[plustek] ># For parport devices use the parport section<
[plustek] >#<
[plustek] ># [parport]<
[plustek] ># device /dev/pt drv<
[plustek] ><
[plustek] >#<
[plustek] ># leave the default values as specified in /etc/modules.conf<
[plustek] >#<
[plustek] >#option warmup    -1<
[plustek] >#option lOffOnEnd -1<
[plustek] >#option lampOff   -1<
[plustek] ><
[plustek] ><
[plustek] >#<
[plustek] ># The USB section:<
[plustek] ># each device needs at least two lines:<
[plustek] ># - [usb] vendor-ID and product-ID<
[plustek] ># - device devicename<
[plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)<
[plustek] ># [usb] 0x07B3 0x0017<
[plustek] ># device /dev/usbscanner<
[plustek] >#<
[plustek] ># additionally you can specify some options<
[plustek] ># warmup, lOffOnEnd, lampOff<
[plustek] >#<
[plustek] ># For autodetection use<
[plustek] >[usb] 0x03f0 0x0605<
[plustek] next device is a USB device (0x03F0-0x0605)
[plustek] next device is an USB device
[plustek] >device /dev/usb/scanner0<
[plustek] Decoding device name >/dev/usb/scanner0<
[pl....
[plustek] drvopen()
[plustek] usbDev open(/dev/usb/scanner0,0x03F0-0x0605)
[plustek] Vendor ID=0x03F0, Product ID=0x0605
[plustek] usbio DetectLM983x
[plustek] UIO error
[plustek] This is not a LM9831 or LM9832 chip based scanner.
[plustek] open failed: -1
[dll] init: backend `plustek' is version 1.0.0
[plustek] sane get devices (0xbffff068, 0)

No scanners were identified. If you w..."

On Mandrake 9. 
Thanks if you could help me