plustek: Thread: how to put the lamp off ?

Hi all,

I use a parallel port plustek scanner (optic pro 
9636T) and the direct device parport0.
It works fine but i would like to put the lamp off 
when i don't use my scanner .
Is it possible ? If so, how could i do that ?

Thanks for your response.

Cheers


-- 
Jacques

Jacques Montier wrote:

> Hi all,
>
> I use a parallel port plustek scanner (optic pro 9636T) and the direct 
> device parport0.
> It works fine but i would like to put the lamp off when i don't use my 
> scanner .
> Is it possible ? If so, how could i do that ?
>
> Thanks for your response.
>
> Cheers
>
>


In my sane-plustek I've found that
You must put it in your /etc/sane.d/plustek_pp.conf i think.

option lampOff t
              t is the time in seconds for switching off the lamps in  
standby
              mode


I have the same parallel scanner which kernel version do you run for 
working?

In my case, (kernel 2.4 doesn't recognize device)
                   (kernel 2.6 modules don't compile)

Can you or someone else help me?

Thanks

Nanouck

Hi,

On Monday 19 July 2004 19:20, Nicolas DELY wrote:
[SNIPSNAP]
>
> option lampOff t
>               t is the time in seconds for switching off the lamps in
>               standby  mode

That correct, see also man sane_plustek_pp

option lampOffOnEnd switches the lamp off when leaving the backend.

> I have the same parallel scanner which kernel version do you run for
> working?
>
> In my case, (kernel 2.4 doesn't recognize device)
>                    (kernel 2.6 modules don't compile)
>
> Can you or someone else help me?

Try the latest version from CVS, the module compilation issues should be
fixed now. but I recommend to use the user mode drivers. What is you 
configuration?

Gerhard

Hi,

please don't send the mails directly to me, use the list!!!

Datum: 20.07.2004 11:42
Von: Jacques Montier ####@####.####
[SNIPSNAP]
>
> Well, this does not work for me.
> After a scan, lamp is still on.
> Here is my modules.conf configuration :
> alias char-major-40 pt_drv
> options pt_drv port=0x378 forceMode=0 lOffonEnd=1
> mov=0 warmup=15 slowIO=0 lampoff=180
>
> Here is my plustek_pp.conf :
>
> [direct]
> device 0x378
>
> #
> # leave the default values as specified in
> /etc/modules.conf
> #
> option warmup -1
> option lOffOnEnd -1
> option lampOff -1
>
> [direct]
> device parport0
>
> my lamp should be off after 180 s ?...
> I tried to put lOffonEnd=0 to switch off the lamp
> after scanning, but it does not work either.
>
> thanks for your help.

When you're using the module, then your plustek_pp.conf will not work!
Can you please send the output of the following command to the list:
export SANE_DEBUG_PLUSTEK_PP=20 ; scanimage -L

You might also change
option lOffOnEnd 1
option lampOff 180

Ciao,
  Gerhard

Gerhard Jaeger a écrit :
> Hi,
> When you're using the module, then your plustek_pp.conf will not work!
> Can you please send the output of the following command to the list:
> export SANE_DEBUG_PLUSTEK_PP=20 ; scanimage -L
> 
> You might also change
> option lOffOnEnd 1
> option lampOff 180
> 
> Ciao,
>   Gerhard

Hi,

Here it is,

[plustek_pp] PlustekPP backend V0.01-8, part of 
sane-backends 1.0.14
[plustek_pp] ># Plustek-PP SANE Backend 
configuration file<
[plustek_pp] ># For use with Plustek parallel-port 
scanners<
[plustek_pp] >#<
[plustek_pp] ><
[plustek_pp] >#<
[plustek_pp] ># user either [direct] or [kernel] 
to access the scanner<
[plustek_pp] ># when using [kernel], device 
specifies the device-node, which is created<
[plustek_pp] ># by the kernel-module loader 
(applies only to Linux)<
[plustek_pp] ># when using [direct], device is 
used to set the parallel-port base address<
[plustek_pp] ># or a device-name suitable for 
libieee1284, i.e. parport0<
[plustek_pp] >#<
[plustek_pp] >[direct]<
[plustek_pp] >device 0x378<
[plustek_pp] Decoding device name >0x378<
[plustek_pp] ><
[plustek_pp] >#<
[plustek_pp] ># leave the default values as 
specified in /etc/modules.conf<
[plustek_pp] >#<
[plustek_pp] >option warmup -1<
[plustek_pp] Decoding option >warmup<
[plustek_pp] >option lOffOnEnd -1<
[plustek_pp] Decoding option >lOffOnEnd<
[plustek_pp] >option lampOff -1<
[plustek_pp] Decoding option >lampOff<
[plustek_pp] ><
[plustek_pp] ># model override switch, mostly for 
cosmetic changes, if the autodetection<
[plustek_pp] ># does not work or could not work 
correctly<
[plustek_pp] >#option mov 7<
[plustek_pp] ><
[plustek_pp] >#<
[plustek_pp] ># example for accessing the scanner 
via libieee1284<
[plustek_pp] >#<
[plustek_pp] >[direct]<
[plustek_pp] attach (0x378, 0xbfffc2d0, (nil))
[plustek_pp] Device configuration:
[plustek_pp] device name   : >0x378<
[plustek_pp] direct I/O    : yes
[plustek_pp] warmup        : -1s
[plustek_pp] lampOff       : -1
[plustek_pp] lampOffOnEnd  : yes
[plustek_pp] model override: 0
[plustek_pp] ---------------------
[plustek_pp] drvopen()
[plustek_pp] open: PtDrvInit failed: 4
[plustek_pp] open failed: -1
[plustek_pp] >device parport0<
[plustek_pp] Decoding device name >parport0<
[plustek_pp] ><
[plustek_pp] >#<
[plustek_pp] ># example for accessing the scanner 
via the kernel module<
[plustek_pp] >#<
[plustek_pp] >#[kernel]<
[plustek_pp] >#device /dev/pt_drv<
[plustek_pp] ><
[plustek_pp] >#option warmup    -1<
[plustek_pp] >#option lOffOnEnd -1<
[plustek_pp] >#option lampOff   -1<
[plustek_pp] attach (parport0, 0xbfffc2d0, (nil))
[plustek_pp] Device configuration:
[plustek_pp] device name   : >parport0<
[plustek_pp] direct I/O    : yes
[plustek_pp] warmup        : -1s
[plustek_pp] lampOff       : -1
[plustek_pp] lampOffOnEnd  : yes
[plustek_pp] model override: 0
[plustek_pp] ---------------------
[plustek_pp] drvopen()
[plustek_pp] ptdrvInit(0)
[plustek_pp] Init settings done
[plustek_pp] ScanData = 0x08053f38
[plustek_pp] Assigning port handle 0
[plustek_pp] ptdrvOpen(port=0x0)
[plustek_pp] Try to claim the parport
[plustek_pp] Setting SPP-mode
[plustek_pp] Setting PS/2-mode
[plustek_pp] Setting EPP-mode
[plustek_pp] We're using libIEEE1284 I/O
[plustek_pp] Starting Scanner-Autodetection
[plustek_pp] ************ DETECTP48xx ************
[plustek_pp] ModelSet4800()
[plustek_pp] modelInitPageSettings()
[plustek_pp] A4 set
[plustek_pp] ModelSet4800() done.
[plustek_pp] P48xxInitAsic()
[plustek_pp] DacInitialize()
[plustek_pp] ImageInitialize()
[plustek_pp] IOFuncInitialize()
[plustek_pp] IOInitialize()
[plustek_pp] * using readfunction >fnEPPRead<
[plustek_pp] MotorInitialize()
[plustek_pp] ResetPort()
[plustek_pp] Test 0x55
[plustek_pp] Test 0xAA
[plustek_pp] Compare data=0x40 and status=0x50, 
port=0x0
[plustek_pp] p48xxReadWriteTest()
[plustek_pp] Can't find your model, asic = 0x5a
[plustek_pp] detectScannerConnection() returns -9031.
[plustek_pp] ************* ASIC9800x *************
[plustek_pp] ResetPort()
[plustek_pp] IOInitialize()
[plustek_pp] * using readfunction >fnEPPRead<
[plustek_pp] ASIC = 0x81
[plustek_pp] ************* ASIC98001 *************
[plustek_pp] ModelSet9636()
[plustek_pp] ModelSet9360()
[plustek_pp] modelInitPageSettings()
[plustek_pp] A4 set
[plustek_pp] ModelSet9630() done.
[plustek_pp] modelInitPageSettings()
[plustek_pp] A4 set
[plustek_pp] ModelSet9636() done.
[plustek_pp] P9636InitAsic()
[plustek_pp] DacInitialize()
[plustek_pp] ImageInitialize()
[plustek_pp] IOFuncInitialize()
[plustek_pp] IOInitialize()
[plustek_pp] * using readfunction >fnEPPRead<
[plustek_pp] MotorInitialize()
[plustek_pp] 0x81
[plustek_pp] CCID = 0x00
[plustek_pp] P9636InitAsic() done.
[plustek_pp] ResetPort()
[plustek_pp] Test 0x55
[plustek_pp] Test 0xAA
[plustek_pp] Compare data=0x40 and status=0x10, 
port=0x0
[plustek_pp] ioP98ReadWriteTest()
[plustek_pp] Putting Scanner (ASIC 98001) into 
Idle-Mode
[plustek_pp] detectScannerConnection() returns 0.
[plustek_pp] p9636InitP98001(0)
[plustek_pp] bData = 0x0000, PCB-ID = 0x00
[plustek_pp] CCD-ID = 0x00 = _CCD_3797
[plustek_pp] bSetScanModeFlag = 0
[plustek_pp] *** setupBuffers ***
[plustek_pp] Driverbuf(147360 bytes) needed !
[plustek_pp] pColorRunTab = 0x4007f534 - 0x4007efa8
[plustek_pp] Adjust for 98001 ASIC
[plustek_pp] sb2 = 0x4005b008, sb1 = 0x40065be8, 
Color = 0x40075db8
[plustek_pp] Pro = 0x4007b3a8, size = 147360
[plustek_pp] *** DETECTION DONE, result: 0 ***
[plustek_pp] Switching lamp 0 on.
[plustek_pp] ptdrvClose()
[plustek_pp] *** cleanup buffers ***
[plustek_pp] MiscRestorePort()
[plustek_pp] Releasing parport
[plustek_pp] MiscGetModelName - id = 15
[plustek_pp] pt_drv0: 9636T/12000T found
[plustek_pp] pt_drv0: Lamp-Timer set to 180 seconds.
[plustek_pp] pt_drv0: WarmUp period set to 30 seconds.
[plustek_pp] pt_drv0: Lamp untouched on driver unload.
[plustek_pp] Lamp-Timer started!
[plustek_pp] ioctl(_PTDRV_OPEN_DEVICE)
[plustek_pp] Lamp-Timer stopped!
[plustek_pp] Init settings done
[plustek_pp] ptdrvOpen(port=0x0)
[plustek_pp] Try to claim the parport
[plustek_pp] Setting SPP-mode
[plustek_pp] Setting PS/2-mode
[plustek_pp] Setting EPP-mode
[plustek_pp] We're using libIEEE1284 I/O
[plustek_pp] Starting Scanner-detection (ASIC 98001)
[plustek_pp] ************* ASIC98001 *************
[plustek_pp] ModelSet9636()
[plustek_pp] ModelSet9360()
[plustek_pp] modelInitPageSettings()
[plustek_pp] A4 set
[plustek_pp] ModelSet9630() done.
[plustek_pp] modelInitPageSettings()
[plustek_pp] A4 set
[plustek_pp] ModelSet9636() done.
[plustek_pp] P9636InitAsic()
[plustek_pp] DacInitialize()
[plustek_pp] ImageInitialize()
[plustek_pp] IOFuncInitialize()
[plustek_pp] IOInitialize()
[plustek_pp] * using readfunction >fnEPPRead<
[plustek_pp] MotorInitialize()
[plustek_pp] 0x81
[plustek_pp] CCID = 0x00
[plustek_pp] P9636InitAsic() done.
[plustek_pp] ResetPort()
[plustek_pp] Test 0x55
[plustek_pp] Test 0xAA
[plustek_pp] Compare data=0x40 and status=0x10, 
port=0x0
[plustek_pp] ioP98ReadWriteTest()
[plustek_pp] Putting Scanner (ASIC 98001) into 
Idle-Mode
[plustek_pp] detectScannerConnection() returns 0.
[plustek_pp] p9636InitP98001(0)
[plustek_pp] bData = 0x0000, PCB-ID = 0x00
[plustek_pp] CCD-ID = 0x00 = _CCD_3797
[plustek_pp] bSetScanModeFlag = 0
[plustek_pp] *** setupBuffers ***
[plustek_pp] Driverbuf(147360 bytes) needed !
[plustek_pp] pColorRunTab = 0x4007f534 - 0x4007efa8
[plustek_pp] Adjust for 98001 ASIC
[plustek_pp] sb2 = 0x4005b008, sb1 = 0x40065be8, 
Color = 0x40075db8
[plustek_pp] Pro = 0x4007b3a8, size = 147360
[plustek_pp] *** DETECTION DONE, result: 0 ***
[plustek_pp] ioctl(_PTDRV_ADJUST)
[plustek_pp] Adjusting device 0
[plustek_pp] warmup:       -1
[plustek_pp] lampOff:      -1
[plustek_pp] lampOffOnEnd: -1
[plustek_pp] ioctl(_PTDRV_GET_CAPABILITES)
[plustek_pp] ioctl(_PTDRV_GET_LENSINFO)
[plustek_pp] Scanner information:
[plustek_pp] Vendor : Plustek
[plustek_pp] Model  : 9636T/12000T
[plustek_pp] Asic   : 0x81
[plustek_pp] Flags  : 0x00000280
[plustek_pp] Version: 0x00002c00
[plustek_pp] drvclose()
[plustek_pp] ioctl(_PTDRV_STOP_SCAN)
[plustek_pp] Waiting for Sensor to be back in position
[plustek_pp] - done !
[plustek_pp] ioctl(_PTDRV_CLOSE_DEVICE)
[plustek_pp] *** cleanup buffers ***
[plustek_pp] Putting Scanner (ASIC 98001) into 
Idle-Mode
[plustek_pp] Lamp-Timer started!
[plustek_pp] ptdrvClose()
[plustek_pp] MiscRestorePort()
[plustek_pp] Releasing parport
[plustek_pp] attach: model = >9636T/12000T<
[plustek_pp] sane_get_devices (0xbfffe39c, 0)
device `v4l:/dev/video0' is a Noname Philips 675 
webcam virtual device
device `plustek_pp:parport0' is a Plustek 
9636T/12000T parallel port flatbed scanner
[plustek_pp] sane_exit
[plustek_pp] ptdrvShutdown()
[plustek_pp] cleanup device 0
[plustek_pp] Lamp-Timer stopped!
[plustek_pp] Try to claim the parport
[plustek_pp] Putting Scanner (ASIC 98001) into 
Idle-Mode
[plustek_pp] Releasing parport


Thanks

-- 
Jacques

Hi Jacques,

try the following plustek_pp.conf:

[direct]
device parport0

option warmup    30
option lOffOnEnd 1
option lampOff   180

This should fix your problem.
Ciao,
  Gerhard


On Tuesday 20 July 2004 12:20, Jacques Montier wrote:
> Gerhard Jaeger a écrit :
> > Hi,
> > When you're using the module, then your plustek_pp.conf will not work!
> > Can you please send the output of the following command to the list:
> > export SANE_DEBUG_PLUSTEK_PP=20 ; scanimage -L
> >
> > You might also change
> > option lOffOnEnd 1
> > option lampOff 180
> >
> > Ciao,
> >   Gerhard
>
> Hi,
>
> Here it is,
>
> [plustek_pp] PlustekPP backend V0.01-8, part of
> sane-backends 1.0.14
> [plustek_pp] ># Plustek-PP SANE Backend
> configuration file<
> [plustek_pp] ># For use with Plustek parallel-port
> scanners<
> [plustek_pp] >#<
> [plustek_pp] ><
> [plustek_pp] >#<
> [plustek_pp] ># user either [direct] or [kernel]
> to access the scanner<
> [plustek_pp] ># when using [kernel], device
> specifies the device-node, which is created<
> [plustek_pp] ># by the kernel-module loader
> (applies only to Linux)<
> [plustek_pp] ># when using [direct], device is
> used to set the parallel-port base address<
> [plustek_pp] ># or a device-name suitable for
> libieee1284, i.e. parport0<
> [plustek_pp] >#<
> [plustek_pp] >[direct]<
> [plustek_pp] >device 0x378<
> [plustek_pp] Decoding device name >0x378<
> [plustek_pp] ><
> [plustek_pp] >#<
> [plustek_pp] ># leave the default values as
> specified in /etc/modules.conf<
> [plustek_pp] >#<
> [plustek_pp] >option warmup -1<
> [plustek_pp] Decoding option >warmup<
> [plustek_pp] >option lOffOnEnd -1<
> [plustek_pp] Decoding option >lOffOnEnd<
> [plustek_pp] >option lampOff -1<
> [plustek_pp] Decoding option >lampOff<
> [plustek_pp] ><
> [plustek_pp] ># model override switch, mostly for
> cosmetic changes, if the autodetection<
> [plustek_pp] ># does not work or could not work
> correctly<
> [plustek_pp] >#option mov 7<
> [plustek_pp] ><
> [plustek_pp] >#<
> [plustek_pp] ># example for accessing the scanner
> via libieee1284<
> [plustek_pp] >#<
> [plustek_pp] >[direct]<
> [plustek_pp] attach (0x378, 0xbfffc2d0, (nil))
> [plustek_pp] Device configuration:
> [plustek_pp] device name   : >0x378<
> [plustek_pp] direct I/O    : yes
> [plustek_pp] warmup        : -1s
> [plustek_pp] lampOff       : -1
> [plustek_pp] lampOffOnEnd  : yes
> [plustek_pp] model override: 0
> [plustek_pp] ---------------------
> [plustek_pp] drvopen()
> [plustek_pp] open: PtDrvInit failed: 4
> [plustek_pp] open failed: -1
> [plustek_pp] >device parport0<
> [plustek_pp] Decoding device name >parport0<
> [plustek_pp] ><
> [plustek_pp] >#<
> [plustek_pp] ># example for accessing the scanner
> via the kernel module<
> [plustek_pp] >#<
> [plustek_pp] >#[kernel]<
> [plustek_pp] >#device /dev/pt_drv<
> [plustek_pp] ><
> [plustek_pp] >#option warmup    -1<
> [plustek_pp] >#option lOffOnEnd -1<
> [plustek_pp] >#option lampOff   -1<
> [plustek_pp] attach (parport0, 0xbfffc2d0, (nil))
> [plustek_pp] Device configuration:
> [plustek_pp] device name   : >parport0<
> [plustek_pp] direct I/O    : yes
> [plustek_pp] warmup        : -1s
> [plustek_pp] lampOff       : -1
> [plustek_pp] lampOffOnEnd  : yes
> [plustek_pp] model override: 0
> [plustek_pp] ---------------------
> [plustek_pp] drvopen()
> [plustek_pp] ptdrvInit(0)
> [plustek_pp] Init settings done
> [plustek_pp] ScanData = 0x08053f38
> [plustek_pp] Assigning port handle 0
> [plustek_pp] ptdrvOpen(port=0x0)
> [plustek_pp] Try to claim the parport
> [plustek_pp] Setting SPP-mode
> [plustek_pp] Setting PS/2-mode
> [plustek_pp] Setting EPP-mode
> [plustek_pp] We're using libIEEE1284 I/O
> [plustek_pp] Starting Scanner-Autodetection
> [plustek_pp] ************ DETECTP48xx ************
> [plustek_pp] ModelSet4800()
> [plustek_pp] modelInitPageSettings()
> [plustek_pp] A4 set
> [plustek_pp] ModelSet4800() done.
> [plustek_pp] P48xxInitAsic()
> [plustek_pp] DacInitialize()
> [plustek_pp] ImageInitialize()
> [plustek_pp] IOFuncInitialize()
> [plustek_pp] IOInitialize()
> [plustek_pp] * using readfunction >fnEPPRead<
> [plustek_pp] MotorInitialize()
> [plustek_pp] ResetPort()
> [plustek_pp] Test 0x55
> [plustek_pp] Test 0xAA
> [plustek_pp] Compare data=0x40 and status=0x50,
> port=0x0
> [plustek_pp] p48xxReadWriteTest()
> [plustek_pp] Can't find your model, asic = 0x5a
> [plustek_pp] detectScannerConnection() returns -9031.
> [plustek_pp] ************* ASIC9800x *************
> [plustek_pp] ResetPort()
> [plustek_pp] IOInitialize()
> [plustek_pp] * using readfunction >fnEPPRead<
> [plustek_pp] ASIC = 0x81
> [plustek_pp] ************* ASIC98001 *************
> [plustek_pp] ModelSet9636()
> [plustek_pp] ModelSet9360()
> [plustek_pp] modelInitPageSettings()
> [plustek_pp] A4 set
> [plustek_pp] ModelSet9630() done.
> [plustek_pp] modelInitPageSettings()
> [plustek_pp] A4 set
> [plustek_pp] ModelSet9636() done.
> [plustek_pp] P9636InitAsic()
> [plustek_pp] DacInitialize()
> [plustek_pp] ImageInitialize()
> [plustek_pp] IOFuncInitialize()
> [plustek_pp] IOInitialize()
> [plustek_pp] * using readfunction >fnEPPRead<
> [plustek_pp] MotorInitialize()
> [plustek_pp] 0x81
> [plustek_pp] CCID = 0x00
> [plustek_pp] P9636InitAsic() done.
> [plustek_pp] ResetPort()
> [plustek_pp] Test 0x55
> [plustek_pp] Test 0xAA
> [plustek_pp] Compare data=0x40 and status=0x10,
> port=0x0
> [plustek_pp] ioP98ReadWriteTest()
> [plustek_pp] Putting Scanner (ASIC 98001) into
> Idle-Mode
> [plustek_pp] detectScannerConnection() returns 0.
> [plustek_pp] p9636InitP98001(0)
> [plustek_pp] bData = 0x0000, PCB-ID = 0x00
> [plustek_pp] CCD-ID = 0x00 = _CCD_3797
> [plustek_pp] bSetScanModeFlag = 0
> [plustek_pp] *** setupBuffers ***
> [plustek_pp] Driverbuf(147360 bytes) needed !
> [plustek_pp] pColorRunTab = 0x4007f534 - 0x4007efa8
> [plustek_pp] Adjust for 98001 ASIC
> [plustek_pp] sb2 = 0x4005b008, sb1 = 0x40065be8,
> Color = 0x40075db8
> [plustek_pp] Pro = 0x4007b3a8, size = 147360
> [plustek_pp] *** DETECTION DONE, result: 0 ***
> [plustek_pp] Switching lamp 0 on.
> [plustek_pp] ptdrvClose()
> [plustek_pp] *** cleanup buffers ***
> [plustek_pp] MiscRestorePort()
> [plustek_pp] Releasing parport
> [plustek_pp] MiscGetModelName - id = 15
> [plustek_pp] pt_drv0: 9636T/12000T found
> [plustek_pp] pt_drv0: Lamp-Timer set to 180 seconds.
> [plustek_pp] pt_drv0: WarmUp period set to 30 seconds.
> [plustek_pp] pt_drv0: Lamp untouched on driver unload.
> [plustek_pp] Lamp-Timer started!
> [plustek_pp] ioctl(_PTDRV_OPEN_DEVICE)
> [plustek_pp] Lamp-Timer stopped!
> [plustek_pp] Init settings done
> [plustek_pp] ptdrvOpen(port=0x0)
> [plustek_pp] Try to claim the parport
> [plustek_pp] Setting SPP-mode
> [plustek_pp] Setting PS/2-mode
> [plustek_pp] Setting EPP-mode
> [plustek_pp] We're using libIEEE1284 I/O
> [plustek_pp] Starting Scanner-detection (ASIC 98001)
> [plustek_pp] ************* ASIC98001 *************
> [plustek_pp] ModelSet9636()
> [plustek_pp] ModelSet9360()
> [plustek_pp] modelInitPageSettings()
> [plustek_pp] A4 set
> [plustek_pp] ModelSet9630() done.
> [plustek_pp] modelInitPageSettings()
> [plustek_pp] A4 set
> [plustek_pp] ModelSet9636() done.
> [plustek_pp] P9636InitAsic()
> [plustek_pp] DacInitialize()
> [plustek_pp] ImageInitialize()
> [plustek_pp] IOFuncInitialize()
> [plustek_pp] IOInitialize()
> [plustek_pp] * using readfunction >fnEPPRead<
> [plustek_pp] MotorInitialize()
> [plustek_pp] 0x81
> [plustek_pp] CCID = 0x00
> [plustek_pp] P9636InitAsic() done.
> [plustek_pp] ResetPort()
> [plustek_pp] Test 0x55
> [plustek_pp] Test 0xAA
> [plustek_pp] Compare data=0x40 and status=0x10,
> port=0x0
> [plustek_pp] ioP98ReadWriteTest()
> [plustek_pp] Putting Scanner (ASIC 98001) into
> Idle-Mode
> [plustek_pp] detectScannerConnection() returns 0.
> [plustek_pp] p9636InitP98001(0)
> [plustek_pp] bData = 0x0000, PCB-ID = 0x00
> [plustek_pp] CCD-ID = 0x00 = _CCD_3797
> [plustek_pp] bSetScanModeFlag = 0
> [plustek_pp] *** setupBuffers ***
> [plustek_pp] Driverbuf(147360 bytes) needed !
> [plustek_pp] pColorRunTab = 0x4007f534 - 0x4007efa8
> [plustek_pp] Adjust for 98001 ASIC
> [plustek_pp] sb2 = 0x4005b008, sb1 = 0x40065be8,
> Color = 0x40075db8
> [plustek_pp] Pro = 0x4007b3a8, size = 147360
> [plustek_pp] *** DETECTION DONE, result: 0 ***
> [plustek_pp] ioctl(_PTDRV_ADJUST)
> [plustek_pp] Adjusting device 0
> [plustek_pp] warmup:       -1
> [plustek_pp] lampOff:      -1
> [plustek_pp] lampOffOnEnd: -1
> [plustek_pp] ioctl(_PTDRV_GET_CAPABILITES)
> [plustek_pp] ioctl(_PTDRV_GET_LENSINFO)
> [plustek_pp] Scanner information:
> [plustek_pp] Vendor : Plustek
> [plustek_pp] Model  : 9636T/12000T
> [plustek_pp] Asic   : 0x81
> [plustek_pp] Flags  : 0x00000280
> [plustek_pp] Version: 0x00002c00
> [plustek_pp] drvclose()
> [plustek_pp] ioctl(_PTDRV_STOP_SCAN)
> [plustek_pp] Waiting for Sensor to be back in position
> [plustek_pp] - done !
> [plustek_pp] ioctl(_PTDRV_CLOSE_DEVICE)
> [plustek_pp] *** cleanup buffers ***
> [plustek_pp] Putting Scanner (ASIC 98001) into
> Idle-Mode
> [plustek_pp] Lamp-Timer started!
> [plustek_pp] ptdrvClose()
> [plustek_pp] MiscRestorePort()
> [plustek_pp] Releasing parport
> [plustek_pp] attach: model = >9636T/12000T<
> [plustek_pp] sane_get_devices (0xbfffe39c, 0)
> device `v4l:/dev/video0' is a Noname Philips 675
> webcam virtual device
> device `plustek_pp:parport0' is a Plustek
> 9636T/12000T parallel port flatbed scanner
> [plustek_pp] sane_exit
> [plustek_pp] ptdrvShutdown()
> [plustek_pp] cleanup device 0
> [plustek_pp] Lamp-Timer stopped!
> [plustek_pp] Try to claim the parport
> [plustek_pp] Putting Scanner (ASIC 98001) into
> Idle-Mode
> [plustek_pp] Releasing parport
>
>
> Thanks

Gerhard Jaeger a écrit :
> Hi Jacques,
> 
> try the following plustek_pp.conf:
> 
> [direct]
> device parport0
> 
> option warmup    30
> option lOffOnEnd 1
> option lampOff   180
> 
> This should fix your problem.
> Ciao,
>   Gerhard
> 

Yes , it works fine now !!!
It's great, thank you very much for your help 
Gerhard !

Cheers
-- 
Jacques

Gerhard Jaeger wrote:

>
>Try the latest version from CVS, the module compilation issues should be
>fixed now. but I recommend to use the user mode drivers. What is you 
>configuration?
>
>Gerhard
>
Hi,

I haven't still test cvs version but you'are talking about cvs sane 
version no?
else can you explain me howto download drivers?

I use udev maybe it is the reason why it doesn't work?

Nanouck

Hi,

please can you explain your problems again?
What system, distribution, kernel are you using?
Which scanner?
Which SANE version?

When I'm talking about the CVS, I mean the daily snapshots from
www.sane-project.org...

Ciao,
  Gerhard

On Wednesday 21 July 2004 19:12, Nicolas DELY wrote:
> Gerhard Jaeger wrote:
> >Try the latest version from CVS, the module compilation issues should be
> >fixed now. but I recommend to use the user mode drivers. What is you
> >configuration?
> >
> >Gerhard
>
> Hi,
>
> I haven't still test cvs version but you'are talking about cvs sane
> version no?
> else can you explain me howto download drivers?
>
> I use udev maybe it is the reason why it doesn't work?
>
> Nanouck

Gerhard Jaeger wrote:

>Hi,
>
>please can you explain your problems again?
>What system, distribution, kernel are you using?
>Which scanner?
>Which SANE version?
>
>When I'm talking about the CVS, I mean the daily snapshots from
>www.sane-project.org...
>
>Ciao,
>  Gerhard
>  
>
Excuse me, I'm very confuse too with this scanner.

I have a gentoo with a linux-2.6.7-gentoo-r11 kernel, i can join my .config

I have emerged:
- sane-backend 1.0.14-r3
- sane-frontends  1.0.12
- xsane 0.93

my scanner is a plustek optic-pro 9636T with parrallel interface, it's 
not a reference but i know it works fine on my M$

Important: _i use udev_
 

What are the commands to do?

modprobe ppdev?

how can i detect my scanner?

thanks for help Gerhard